Users can choose to restore factory defaults for the device or system. When restoring factory defaults, these settings are reset to their original factory settings:
Control Unit Factory Defaults
|
Control Unit Factory Settings |
||
|
Control Unit Setting |
Control Unit Default |
Reset by “Restore Defaults” |
|
CU Name (Long) |
CCU_xx_01 |
X |
|
CU Name (Short) |
CCU_xx_01 |
X |
|
Contrast |
3 |
X |
|
Backlight Brightness |
High |
X |
|
Talk LED Brightness |
High |
X |
|
Sync Priority |
Master |
X |
|
Intercom Type |
OFF |
X |
|
Intercom Call |
OFF |
X |
|
Intercom Mic Kill |
OFF |
X |
|
Intercom Echo Can |
ON (2-Wire); OFF (4-Wire) |
X |
|
Intercom IN (2w/4w) |
2W: 0 |
X |
|
Intercom OUT (2w/4w) |
2W: 0 |
X |
|
Auxiliary IN |
0 |
X |
|
Auxiliary OUT |
0 |
X |
|
SA Relay |
Enable |
X |
|
SA Audio |
0 |
X |
|
Local Conference |
None |
|
|
Local Mic Type |
Auto Detect |
X |
|
Local Mic Gain (Dynamic) |
6 (+23 dB) |
X |
|
Local Mic Gain (Electret) |
3 (−4 dB) |
X |
|
Local Sidetone |
Med (−12 dB) |
X |
|
TCP/IP Mode |
Manual |
X |
|
Access Rights |
Admin |
X * |
*Resets only if system was Auto Configured; does not reset if CCF was uploaded.
Note: Restoring CU factory defaults, as well as clearing an RP's memory, erases RP pairing information. If you have saved the CCF (See Save Configuration File (CCF)), the pairing is still visible in the CCF.
Radio Pack Factory Defaults
- Access the RP menu and select Tech Menu. Press F2 (ENT).
- Scroll and select Factory Defaults press F2 (ENT) to enter view reset options.
- Scroll and select Restore Defaults or Clear Memory and press F2 (ENT).
- Confirm your selection by selecting either Yes or No.
The table below lists the settings that are affected when restoring RP factory defaults or clearing RP memory.
Note: Restore Defaults resets the RP to the default settings for the assigned profile. Clear Memory erases the RP pairing information and profile assignment from the device. After clearing memory, the pairing is still visible in the CCF, but since the RP has no Profile assignment, you must re-pair the RP to begin using it again. RP settings will default to those of the profile chosen during pairing. Exceptions to these are listed in the table below.
|
Radio Pack Factory Settings |
|||
|
Radio Pack Setting |
Radio Pack Default |
Reset by “Restore Defaults” |
Reset by "Clear Memory" |
|---|---|---|---|
|
Pack Name (Long) |
ESN# |
X |
|
|
Pack Name (Short) |
ESN# |
X |
|
|
Battery Alert |
Both |
X |
X |
|
Contrast (not applicable to CRP-C12) |
7 |
X |
X |
|
Backlight Brightness |
High |
X |
X |
|
Backlight Time Out |
30 seconds |
X |
X |
|
Mic Type |
Auto Detect |
X |
X |
|
Mic Gain (Dynamic) |
6 (+23 dB) |
X |
X |
|
Mic Gain (Electret) |
3 (-4 dB) |
X |
X |
|
Noise Gate |
Low (-75 dB) |
X |
X |
|
Sidetone |
Med (-12 dB) |
X |
X |
|
Minimum Volume (all knobs) (not applicable to CRP-C12) |
0 (off) |
X |
X |
|
Maximum Volume (all knobs) (not applicable to CRP-C12) |
20 (+6 dB) |
X |
X |
|
Talk Tones |
Off |
X |
X |
|
User Rights |
Admin |
Set by System |
Set by System |
| Roaming Bias | Medium | Resets to Medium | Resets to Medium |